XPROG-M V5.60 Read dump from Mercedes W203 EIS Succeed

Here’s  Cartool.co.uk technician shares one customer feedback on using Xprog-m v5.0 to read dump successfully from W203 EIS module, flash and eeprom OK.

ECU: SIM4LKE

Mask: 3K91D

MCU: MC912DC128ACPV

EZS P/N: 209 545 05 08

Type: W211_HC12

Circuit board from AK500 key programmer:

the test points to solder to the EIS board

eis-board
the signal names from this image:

19 -BKGD
7-rest
8-XTAL
24-GND
1-VDDR
26-GND

good connection for your EZS:

hc12

Finally I can read dumps by Xprog. Confirmed, flash and eeprom OK.

Dumps: w211_hc12_ezs.rar

https://mega.nz/#!J5VDzArS!QNncVYvh6TzISkNRCsXE2n4TP6A7etqjDrGowzfsmaY

*** some tips of the EZS: (from a user)

if you can’t connect with SD and dash says ‘—-‘, then is your EZS dead. It could happened when you tried to connect it with xprog, or it went just broken itself. Could be question of flash it and “eeprom it”, but it can be also the MCU is dead. then you’ll need or MCU exchange or use another EZS.

No matter you buy MCU or EZS, you have to do this:

Put in EZS eeprom correct VIN, because otherwise you will have problem with airbag and ecu’s sync (this EZS nr. can be from diesel or petrol car), put there the same km’s like in dash board, otherwise the ‘—-‘ may not disappear, then you’ll need to calc and prog the keys.

After this you’ll need to virginize engine ECU and ESL.
Install everything back, and make it work with SD.

New Arrival Xprog M V5.60 Xprog Box ECU Programmer

Cartool.co.uk New Released XPROG-M V5.60 Xprog Box ECU Programmer 2016 Newest Version adds more ecu chip authorizations.

Xprog V5.60 feature& function:

Language: English

Newest Version: V5.60

Operating system: Windows XP 32-bit or Windows 7 64-bit

 

XPROG-M V5.60 Authorizations:

AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM)

AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM)

AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM)

AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)

AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM)

AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0007 ST M35080 authorization. Read/Write/Erase device to delivery state.

AUTH-0008 BMW EWS3 authorization

AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory)

AUTH-0010 MB ZGS001 authorization

AUTH-0011 Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory)

AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory)

AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash)

AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size)

AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0020 ARM (Micronas, …) Family authorization (allows to read/write internal flash and external serial EEPROM)

AUTH-0021 ARM (Micronas, …) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage,chassis number (VIN), serial number and PIN code).

AUTH-0023-1 MAC7xxx(New added)

AUTH-0023-2 XC23xx(New added)

AUTH-0024-1 MC9S12Cxx(New added)

AUTH-0024-2 MC9S12XE(New added)

AUTH-0024-3 9S12XE SECURITY

AUTH-0024-4 MC9S12HA/HY/P

AUTH-0025-1 MPC/SPC5xxx (newly added)

Xprog-m v5.60 Hardware Software information shown as below:

xprog-m-v5.60-display

Xprog-m Box Update Tips:
1. If your Xprog is older version,cannot use this newest dongle to update to V5.60

2. Close all of the computer anti-software. If not, X-prog software may be killed.

3. Disconnect the internet. If not, the internet may damage the hardware.

4. Uninstall all the old xprog-m, or xprog box software, make sure that your PC only install our software for our xprog-box 5.60 , our xprog-box hardware cannot work with other lower or higher software. If not, the hardware will be damaged, and will lose its warranty…

5. Never try to UPDATE, the hardware will be damaged if you want to try to upgrade it online, without any warranty.

6. We cannot refund, cannot exchange, can not repair if you do not listen to those advices. It means that you accept those conditions if you have ordered our xprog-box

What’s the difference between Xprog V5.60 and Xprog-m V5.55?

Compared with Xprog v5.55, Xprog-m 5.60 have additional function as follow photos shows:

Xprog-V5.60-vs-Xprog-m-V5.55-1

Xprog-V5.60-vs-Xprog-m-V5.55-2

Xprog-V5.60-vs-Xprog-m-V5.55-3

ATMEGA64 Repair Chip Update XPROG-M V5.55 Include CAS4

ATMEGA64 Repair Chip can update any version of XPROG-M programmer to latest V5.55. Before other version, the factory engineers are always bothered by the software problem, now stable software are available. The technicians have tested different version from V5.0 to V5.55, all version works stable and great.

atmega64-repair-chip-update-xprog-m-programmer-include-cas4-001 atmega64-repair-chip-update-xprog-m-programmer-include-cas4-002

 

 

 

 

 

What can ATMEGA64 update chip and Software work on?

1. European solution on XPROG-M software, tested for all versions, very reliable.
2. Support any XPROG-M Version update, can update to latest V5.55
3. Support ALL authorizations.

How to use ATMEGA64 Repair Chip ?

First, you need have XPROG-M Hardware, no matter your hardware is which version, all can use our update chip and software.
Second, we ship from the update chip and software fro European directly by post service.
Third, Solder new Atmega64 MCU to your xprog. Overwrite all files and folders from Xprog_Preinstalled,to your native Xprog install. Usually c:\Program Files\ELDB\Xprog or c:\Program Files(X86)\ELDB\Xprog.
You can now start and Run Xprog. If you want to use this version on brand new PC, please install Xprog 5.0 and Adobe acrobat reader prior to files copy.

 

atmega64-repair-chip-update-xprog-m-programmer-include-cas4-003